News Industry News Details
Industry NewsKai Xin new intelligent temperature alarm operating instructions
Time: 2020-09-29 View: 1998
Kai Weixin manufacturer has developed an intelligent temperature sensing alarm which can detect the temperature rise on site during fire and send alarm signals in time. It is suitable for places where there is too much air and dust to install smoke detection alarms. The alarm adopts the temperature sensing device and the fine production craft, the work is stable, the appearance is beautiful, the installation is simple, does not need the debugging, may be widely used in the hotel, the store, the Internet bar, the song and dance hall, the coffee shop, the leisure hall, the residence and so on place to conduct the fire safety monitoring. The alarm has a built-in buzzer, which makes a strong sound after alarm. The alarm is powered by 3V battery, which consumes very little power and lasts for more than a year. The instructions are as follows:
Normal state: the red indicator light is on for about 50 seconds, and it automatically detects the temperature in the surrounding environment about every 8S.
Failure status: When the alarm´s battery is lower than 2.4V, the alarm beeps around 50S, indicating the battery is under-voltage. In the alarm remind undervoltage, should timely replace the battery, otherwise it will affect the normal work of the alarm.
Alarm state: when the temperature reaches the alarm value, the red indicator lights flickered on, at this time is real fire alarm, when confirmed, alarm quickly ablaze red indicator light, alarm, and through the cloud call broadcast alarm sensor specific information, send alarm sensor location of short messages to mobile phones, mobile phone client to push the probe specific information such as three ways to inform alarm information, to facilitate the administrator immediately found in alert, when the temperature dropped to a certain threshold, the alarm status can be automatically restored.
Self-check status: The alarm should be self-checked regularly. When the button is pressed, the red indicator lights up and sends out the alarm sound. After the button is released, the alarm will automatically return to the normal working state.
Silencing state: in the alarm state, press the button once, the alarm will enter silencing state. In the muffled state, the alarm system stops and the red indicator light flashes quickly. After about 85 seconds of silencing, the alarm will automatically quit the silencing state. If the temperature is still higher than the alarm, the alarm will start again.
If the temperature has decreased, the alarm will automatically enter the normal monitoring working state.
I. Alarm function test
Detectors must be tested after installation or after each scheduled maintenance.
During the test, use a hot hair dryer to blow the thermistor 15CM away from the detector until the detector alarms (confirm that the lamp is always on). It is forbidden to bake detector directly by open fire to avoid burning detector or fire.
2. Maintenance
In the process of use, in case of failure, please contact the supplier as soon as possible, do not disassemble and repair privately, so as to avoid accidents.
If not used for a long time, it is necessary to remove the alarm, and take out the battery, put it in the packing box, and store it in a dry and ventilated place.
Transportation and storage
Transport and storage in accordance with GB/T15464-1995 General Technical Conditions for Instrumentation Packaging.
In the process of transportation and storage, the original packaging and seal of the factory must be kept intact to ensure that the products are not severely impacted.
Drastic changes in ambient temperature should be avoided.
The stacking height shall not exceed 6 layers, and the stacking height of individual pieces shall not exceed 5 layers after unpacking.
Iv. Open the box for inspection
In the packing box: 60 PCS
Inside the box: 1 alarm
The bottom one
One copy of operation instruction
Two expansion plugs
Self tapping screw 2
Normal state: the red indicator light is on for about 50 seconds, and it automatically detects the temperature in the surrounding environment about every 8S.
Failure status: When the alarm´s battery is lower than 2.4V, the alarm beeps around 50S, indicating the battery is under-voltage. In the alarm remind undervoltage, should timely replace the battery, otherwise it will affect the normal work of the alarm.
Alarm state: when the temperature reaches the alarm value, the red indicator lights flickered on, at this time is real fire alarm, when confirmed, alarm quickly ablaze red indicator light, alarm, and through the cloud call broadcast alarm sensor specific information, send alarm sensor location of short messages to mobile phones, mobile phone client to push the probe specific information such as three ways to inform alarm information, to facilitate the administrator immediately found in alert, when the temperature dropped to a certain threshold, the alarm status can be automatically restored.
Self-check status: The alarm should be self-checked regularly. When the button is pressed, the red indicator lights up and sends out the alarm sound. After the button is released, the alarm will automatically return to the normal working state.
Silencing state: in the alarm state, press the button once, the alarm will enter silencing state. In the muffled state, the alarm system stops and the red indicator light flashes quickly. After about 85 seconds of silencing, the alarm will automatically quit the silencing state. If the temperature is still higher than the alarm, the alarm will start again.
If the temperature has decreased, the alarm will automatically enter the normal monitoring working state.
I. Alarm function test
Detectors must be tested after installation or after each scheduled maintenance.
During the test, use a hot hair dryer to blow the thermistor 15CM away from the detector until the detector alarms (confirm that the lamp is always on). It is forbidden to bake detector directly by open fire to avoid burning detector or fire.
2. Maintenance
In the process of use, in case of failure, please contact the supplier as soon as possible, do not disassemble and repair privately, so as to avoid accidents.
If not used for a long time, it is necessary to remove the alarm, and take out the battery, put it in the packing box, and store it in a dry and ventilated place.
Transportation and storage
Transport and storage in accordance with GB/T15464-1995 General Technical Conditions for Instrumentation Packaging.
In the process of transportation and storage, the original packaging and seal of the factory must be kept intact to ensure that the products are not severely impacted.
Drastic changes in ambient temperature should be avoided.
The stacking height shall not exceed 6 layers, and the stacking height of individual pieces shall not exceed 5 layers after unpacking.
Iv. Open the box for inspection
In the packing box: 60 PCS
Inside the box: 1 alarm
The bottom one
One copy of operation instruction
Two expansion plugs
Self tapping screw 2
